News

Company News

Industry dynamics

FAQ

Introduction of ABS Recycled Material

Most of the recycled ABS recycled materials are secondary processing products made of new materials after ABS waste. If these products are reused, the electrical and flame retardant properties will be reduced, and the heavy metal content will exceed the standard. Moreover, due to the repeated addition of plasticizers, carcinogens will be produced during production and use, which will endanger the health of producers and users for a long time.

03-24

2021

Introduction of ABS Recycled Material
Introduction of ABS Recycled Material

Introduction of PP plastic granules

PP plastic particles are not only semi-finished products in the plastic molding industry, but also raw materials for extrusion, injection molding, hollow blow molding and foaming. Let's introduce the advantages of PP plastic particles: convenient feeding, no need to install a forced feeder in the hopper. The relative density of PP plastic particles is higher than that of powder, and the strength of plastic products is better. The mixture of resin and various solid powder or liquid additives is relatively uniform, and the physical properties of plastic products are relatively uniform. PP plastic granules plastic products color uniformity. PP plastic particles contain less air agent volatile substances, so that plastic products are not easy to produce bubbles. PP plastic

03-22

2021

Introduction of PP plastic granules
Introduction of PP plastic granules

Introduction of ABS Recycled Material

The molding characteristics of ABS recycled materials: amorphous materials, medium fluidity, high moisture absorption, must be fully dried. Plastic parts with a shiny surface should be preheated and dried 80-90 degrees for 3 hours. ABS recycled materials should use higher material temperature and mold temperature, but if the material temperature is too high, it is easy to decompose (decomposition temperature> 270 degrees). For high-precision plastic parts, the mold temperature should be 50-60 degrees, and for high-gloss, high-heat-resistant plastic parts, the mold temperature should be 60-80 degrees. If you need to solve the problem of water pinch, you need to improve the fluidity of the material, use high material temperature, high mold temperature, or

03-18

2021

Introduction of ABS Recycled Material
Introduction of ABS Recycled Material

PP white recycled material is a general plastic used once, after the recycling machine thermal extrusion granulation

PP white recycled material is a common plastic used once, after the recycling machine of thermal extrusion granulation, PP white recycled material is. After the general plastic is used once, it can be used as raw material again after thermal extrusion granulation by the recycling machine. The recycled and extruded white polypropylene product with good whiteness, strength and toughness can be used as raw material again. The recycled and extruded white polypropylene product with good whiteness, strength, toughness, strong impact, good fluidity, strong impact and good fluidity.

12-23

2020

PP white recycled material is a general plastic used once, after the recycling machine thermal extrusion granulation
PP white recycled material is a general plastic used once, after the recycling machine thermal extrusion granulation

Black PP recycled materials: special materials for hollow boards with ordinary injection molding grade, high-gloss and impact-resistant environmental protection grade, wire drawing grade (over 250 mesh) and extrusion grade

12-23

2020

Black PP recycled materials: special materials for hollow boards with ordinary injection molding grade, high-gloss and impact-resistant environmental protection grade, wire drawing grade (over 250 mesh) and extrusion grade
Black PP recycled materials: special materials for hollow boards with ordinary injection molding grade, high-gloss and impact-resistant environmental protection grade, wire drawing grade (over 250 mesh) and extrusion grade

Blue, red, green, yellow, pink, motley, gray PP recycled material is suitable for all kinds of injection grade products

12-23

2020

Blue, red, green, yellow, pink, motley, gray PP recycled material is suitable for all kinds of injection grade products
Blue, red, green, yellow, pink, motley, gray PP recycled material is suitable for all kinds of injection grade products

Willing to sincerely cooperate with colleagues from all walks of life, create brilliant!

12-23

2020

Willing to sincerely cooperate with colleagues from all walks of life, create brilliant!
Willing to sincerely cooperate with colleagues from all walks of life, create brilliant!

Analysis of Factors Restricting the Development of Plastics Industry

12-23

2020

Analysis of Factors Restricting the Development of Plastics Industry
Analysis of Factors Restricting the Development of Plastics Industry
< 1...56575859 > proceed page

Follow Us

Picture Name

Dongguan huazuan plastic material Co., Ltd.

Add.: No. 78, Qiaoli Beimen Industrial Zone, changping town, Dongguan City

Tel: +86-0769  82020719

Sales one: Mr. Chen +86-13802397965

Sales 2: Miss Xia +86-13922971175

Sales 3: Miss Feng +86-13922918732

Fax: +86-769 82308699

Email: lindaxia@cnhzsj.com

Copyright©2023 Dongguan huazuan plastic material Co., Ltd. All Rights Reserved

绿美佳塑胶

Powered by www.300.cn | SEO | City List | Business License